Answer
Transcript
Check to ensure that the odometer displays ODOMETER as the reading.
Turn off the ignition of the vehicle..
To enter Ready mode, hold down the ODOMETER button while pressing and holding the power button. While still holding the ODOMETER button, press and hold the brake button to stop the vehicle.
How can you reset the oil light on a Toyota Prius while keeping this in mind?
Instructions on how to reset the Toyota Prius’ “Oil Change” or “Maintenance Required” light
Step 3: To turn off your Prius, press the Power button 1 more time.
Step 4: With your foot off the brake, push and hold down the ODO button, followed by pressing and holding down the Power button twice (2X)
Also, how can I reset the Prius in the same manner?
Procedure for the Prius 04-09 Press and hold the power button for 30 seconds while keeping your foot on the brake. Remove your finger from the power button and attempt to restart your computer. There shouldn’t be any problems; the vehicle should start, the warning lights should be turned off, and all PCMs should be reset. Should this fail, try again.
Also, how do you reset the oil maintenance light on a 2010 Toyota Prius is a question that comes up from time to time?
The Toyota Prius Oil Maintenance Requirement Light should be reset every three years between 2010 and 2015.
Turn the ignition to the “ON” position without turning on the vehicle.
TRIP A appears on the display after continually pressing the TRIP button.
Turn off the ignition and then turn it back on again.
While pressing and holding the km/h MPH button, flip the POWER button to the ON position one more to complete the process.
My Prius is beeping constantly. What should I do?
In a Generation 2 Prius, Disabling the Reserve Alarm is Method 1 of 3.
Get in your automobile and go!
Then switch off the automobile by pressing the Trip button until ODO appears.
It’s time to get back in the automobile!
For 10 seconds, press and hold the TRIP button.
Shift into reverse by pressing the brake pedal all the way in.
Return to the park position.
Re-activate the reverse beep by pressing the button twice on the controller.
There were 23 related question and answer combinations discovered.
What is the procedure for resetting my oil change reminders?
Some automobiles may flash the word “Reset” or display the figure “100” to indicate that they have 100 percent of their oil life remaining after an oil change has been performed. Start the engine by turning off the ignition and waiting a few minutes. See whether the oil light is still flashing or illuminated on the dashboard. If this is the case, the reset procedure should be followed once again.
A 2006 Toyota Prius has a maintenance light that has to be reset.
To reset the oil maintenance light, press the display until it displays the odometer reading, turn off the power switch, press the power switch to ignition on while holding down the trip metre reset button, keep the trip metre reset button held down for approximately 10 seconds, the display will read 000000, and the light will turn off.
In order to reset my dashboard, please follow these steps.
Using the Warning Lights on the Dash to Reset Them Your vehicle’s hood should be open. Using the pliers, loosen the nut that secures the negative terminal to the battery. Remove the cable from the negative battery terminal to the point where it is no longer connected to anything. Remove the battery from the computer for 10 minutes to check that the machine has been completely reset and restarted.
In what circumstance is the service required indicator lit?
This light indicates that repair is necessary in accordance with the vehicle’s maintenance plan and the amount of driving that has been completed. It is most likely that your car is due for an oil change, which is the most common explanation.
A maintenance needed light may be repaired in a few ways.
Toyota Service Required Indicator Light Press and hold the “on” button on the key. Next, check to see whether the odometer reading is shown on your computer. Once you’ve completed this, turn the key off. Hold down the reset button for the trip metres for several seconds. Finally, while keeping the reset button down, turn the key back to the “on” position, but not all the way to the “start” position.
In the case of a Toyota Prius, what does the red triangle indicate?
Causes that are often seen are as follows: It has been claimed by several Prius drivers that a problem with their battery is the most prevalent source of the red triangle of death light. A problem with the high-voltage battery’s ECU is indicated by the appearance of this code, which may be caused by a variety of factors.
Post Views: 17Spread the love
